Skip to content
Pressurewasher & Patio

How to pressure wash a garage floor

Degrease first, work toward the door, keep the drywall dry.

How to pressure wash a garage floor - CHOMP Concrete Oil Stain Remover
By Mike M.|Last checked: |How we pick

A garage floor is not a driveway with a roof on it. The slab is the same, but three things are different and they decide the whole method: the oil stains are worse and need chemistry before any water, the water has only one way out and you have to drive it there deliberately, and there is drywall, insulation, outlets and stored belongings within splash range. Get those three right and the actual washing is straightforward.

Start with the oil, before anything gets wet

Motor oil, transmission fluid and grease have soaked into the slab rather than sitting on it, and no pressure setting lifts them out. This is the single most common disappointment with this job: people blast a garage floor at 2,500 PSI, remove all the gray film, and are left looking at the same black patches.

A dedicated oil and grease remover draws the stain back out of the pores, which is a completely different mechanism from washing. Apply it to dry concrete, give it the full dwell time on the bottle, and scrub the worst patches with a stiff brush before any water arrives. Old stains may need two applications on separate days — that is normal, not a failure. The product comparison is in best concrete cleaners, and concrete cleaner vs degreaser explains why the all-purpose bottle will not do it.

Then treat the whole slab with a general concrete cleaner. The rest of a garage floor is tire marks, dust and road film, and a concrete formula plus dwell time handles it at low pressure.

Water management is the actual skill

On a driveway, water runs off three sides. In a garage it runs to the lowest point, which might be the door, might be a floor drain, and might be the back corner where you keep cardboard boxes. Find out before you start: pour a bucket in the middle and watch where it goes.

Always work from the back wall toward the open door. Every pass pushes water ahead of it, so if you start at the door you will be chasing a slurry back and forth across the slab for an hour.

Keep the spray angle low and forward. The question people ask most about this job is how to avoid soaking the walls, and the answer is the angle of attack: hold the wand so the fan is nearly parallel to the floor and aimed away from the wall, rather than pointing down at 90 degrees where it throws spray in every direction. Work the last foot beside a wall with the tip angled away from it.

Use a surface cleaner if your machine can drive one. In a garage the housing earns its money twice: it cleans three to five times faster, and the skirt contains the overspray that would otherwise be redecorating your drywall. A 14-inch head suits a mid-size electric; check the flow threshold in the sizing guide first, and how to use a surface cleaner covers the technique.

If there is a floor drain, check where it goes. A garage drain that feeds a storm sewer should not be receiving degreaser run-off. Catch and dispose of the first, heaviest flush from an oil stain rather than sending it straight down.

Protect the things you cannot replace

Outlets and switches. Tape plastic over them. A pressure washer and an outlet at ankle height is the worst combination in the garage, and it is covered in pressure washer safety for beginners.

The bottom of the drywall. Unfinished drywall wicks water upward and stays damp inside the wall cavity long after the surface looks dry. Sheet the lower foot.

Water heaters, furnaces and chest freezers. Move or cover. Burners, vents and compressor coils do not want a jet of water.

The garage door panels and the opener. Clean the door at low pressure and keep spray out of the track, the rollers and the motor unit above you.

Epoxy and sealed floors: a different set of rules

A coated floor is a surface on the concrete, and the failure mode is lifting the coating rather than damaging the slab. Three rules:

Low pressure, wide tip, and never a turbo nozzle. A 40-degree tip at two feet is right. A rotating jet will find any weak spot in the coating and peel it.

No acidic or caustic cleaner. A pH-neutral or mild oxygenated cleaner only — aggressive chemistry dulls epoxy and can soften polyaspartic topcoats.

Never spray a chipped edge or a bubble. Water getting under an edge is how a small chip becomes a sheet of lifted coating. Fix the chip before you wash the floor.

If the floor is only sealed rather than coated, the same logic applies at a lower intensity: a sealer is sacrificial, and a hard wash shortens its life.

When not to do this at all

If the garage is attached and has finished, painted drywall you care about, consider a degreaser, a stiff brush and a mop instead. There is no rule that says a garage floor needs a pressure washer, and the water you cannot get out of a closed room is a genuine downside.

If it is below freezing. Standing water in a garage freezes, and so does a hose. The end-of-season routine is in how to winterize a pressure washer.

If the slab is cracked and crumbling, expect the wash to take material with it. Clean it gently and get it patched.

And when you are finished, you are already set up for the driveway and the apron outside, which is the same job with better drainage — how to pressure wash a driveway.

What to buy for this

CHOMP Concrete Oil Stain Remover - CHOMP pressure washing gear

Motor oil and grease stains specifically

CHOMP Concrete Oil Stain Remover

CHOMP

Our score

A pull-out oil stain remover for garage floors and driveways - the one product here that addresses the stain pressure washing cannot remove.

What it is

  • Concrete oil and grease stain remover
  • For garage floors and driveways

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
7.0
Capability
8.6
Build
8.0
Value
8.2

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Targets oil, which no amount of pressure will lift on its own
  • Draws the stain out of the slab rather than just cleaning the surface
  • Works on old stains that other cleaners ignore

Good to know

It works by sitting, sometimes overnight - a stain bottle rather than a general cleaner.

Simple Green Oxy Solve Concrete and Driveway - Simple Green pressure washing gear

General driveway grime and algae

Simple Green Oxy Solve Concrete and Driveway

Simple Green

Our score

The concrete-specific version of the Oxy Solve line: it handles the gray film and green algae that make a driveway look old, but it is not a degreaser.

What it is

  • Concentrate, 128 fl oz
  • Concrete and driveway formula
  • Unscented

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
8.6
Capability
8.2
Build
8.4
Value
8.6

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Noticeably better on algae than a general cleaner
  • Oxygenated chemistry, so run-off is less harsh on planting beds
  • Covers a large driveway per bottle at the stated dilution

Good to know

Motor oil needs a dedicated degreaser - this is for general grime and algae.

Sun Joe SPX-SC14 14-Inch - Sun Joe pressure washing gear

The best match for an electric machine

Sun Joe SPX-SC14 14-Inch

Sun Joe

Our score

Fourteen inches is the sweet spot for an electric unit: wide enough to save real time, narrow enough that 1.6 to 2 GPM still spins it properly.

What it is

  • 14-inch cleaning width
  • Stainless steel housing
  • Four wheels
  • Universal quick-connect fitting

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
8.6
Capability
8.4
Build
8.4
Value
8.8

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Spins properly on electric machines that choke a 15-inch head
  • Four wheels keep it flat, which is what stops the stripe pattern
  • Stainless housing instead of plastic at a similar price

Good to know

A 14-inch head wants about 1.6 GPM, so check your machine's flow first.

Common questions

Can you pressure wash a garage floor?

Yes, on bare or sealed concrete. Treat oil stains with a degreaser first, protect outlets and the lower drywall, work from the back wall toward the open door, then squeegee the water out and dry it with the door open.

How do I pressure wash a garage floor without getting the walls wet?

Keep the fan nearly parallel to the floor and aimed away from the wall rather than pointing straight down, work the last foot beside a wall with the tip angled outward, and use a surface cleaner if you can - the skirt contains almost all the overspray.

Can you pressure wash an epoxy garage floor?

Carefully. Use a 40-degree tip from two feet, a pH-neutral or mild oxygenated cleaner, and never a turbo nozzle. Do not spray a chipped edge or a bubble - water under the coating lifts it in sheets.

Will a pressure washer remove oil stains from concrete?

Not on its own. Oil soaks into the slab, so it needs a dedicated oil and grease remover with real dwell time to draw it back out. Pressure alone removes the gray film and leaves the black patch.