Skip to content
Pressurewasher & Patio

How to clean a clogged pressure washer nozzle

Two minutes with a wire. Do this before you blame the pump.

How to clean a clogged pressure washer nozzle - Twinkle Star Nozzle Tips, 5-Pack
By Mike M.|Last checked: |How we pick

A pressure washer that suddenly lost its punch, sprays a crooked or split fan, or pulses as you hold the trigger almost always has a partly blocked nozzle tip, and the fix is a wire pushed through the orifice from the spray side — two minutes, no tools you do not already own. Do this before you take anything apart, because the tip is the cheapest and most likely culprit in the whole machine.

Why the tip is nearly always the problem

The orifice on a pressure washer nozzle is tiny — a fraction of a millimeter on a homeowner machine. That is how it generates pressure in the first place: a large volume of water forced through a very small hole. The consequence is that a grain of sand, a flake of rust from an old tap, a fragment of hose liner or a lump of dried detergent is enough to change the spray pattern completely.

Three symptoms, all the same cause. Lost pressure — the hole is partly occluded, so less water gets through. A crooked or split fan — the blockage is sitting to one side of the orifice and deflecting the jet. Pulsing — the obstruction is shifting under pressure. If you have any of those, start here rather than at pressure washer will not build pressure, which is the page for when this fix does not work.

The two-minute method

Kill the pressure first. Machine off, water off, then squeeze the trigger until nothing comes out. A high-pressure hose holds energy after shutdown and a nozzle clearing unexpectedly in your hand is a genuine injury, not a scare story.

Pull the tip out. Draw the quick-connect collar back and the tip lifts free. If your wand threads instead of clicking, it unscrews — and converting it to quick connect is worth doing, which is what the fittings page is for.

Push the wire in from the front. The direction matters. Push from the spray face toward the inlet face, so whatever is lodged in there travels back out the way it arrived instead of being driven deeper into the taper. Most machines ship a cleaning wire; a straightened paperclip or an unwound guitar string works identically. Do not use a drill bit, a nail or anything that can enlarge or score the orifice — a scratched orifice sprays badly forever.

Then back-flush it. This is the step people skip and it is the one that actually finishes the job. Hold the tip under a tap backwards so water runs inlet-side to spray-side, or clip it into the wand the wrong way round and run the machine for ten seconds. The wire loosens the debris; the flush removes it.

Check upstream before you refit. Unscrew the garden hose and look at the inlet screen. If it is coated in silt, that is where your grit came from, and the tip will block again next month unless you deal with it.

How to tell a clogged tip from a worn one

Refit and test on a patch of concrete, not on the thing you were cleaning. A healthy 25-degree or 40-degree tip produces a crisp, even fan with hard edges and a consistent width. After cleaning, if the pattern is still ragged, uneven across its width, misted rather than defined, or narrower than it used to be, the orifice itself is worn out.

Worn tips are not repairable. They are also the single cheapest part of the machine, which is why a spare set is sensible insurance — a five-tip set costs less than an hour of standing in a driveway wondering what is wrong. Get the flow rating right when you buy: tips are rated for a flow range, and a 3.5 GPM-rated set fitted to a 1.2 GPM electric will give you noticeably less pressure than the correctly rated set. The rating map is in pressure washer nozzle colors and the sets themselves in best pressure washer nozzle sets.

Soap tips and turbo nozzles clog differently

The soap tip (65-degree, usually black) blocks with dried detergent rather than grit, because detergent left in the passage overnight hardens. Soak it in warm water for ten minutes rather than attacking it with a wire. The cure is to run clear water through the soap setting for thirty seconds at the end of every session, which also keeps the injector clear — see soap injector not working.

A turbo nozzle has a spinning ceramic orifice inside a housing and cannot be wire-cleaned from the front without risking the internals. Back-flush it, and if it stops spinning or rattles dryly, it has worn out — best turbo nozzles covers replacements.

Surface cleaner jets are the same tiny orifices in a bar. If one of two jets blocks, the head slows or spins unevenly and leaves arcs on the concrete, which is the main cause of the complaint in surface cleaner not spinning.

Stopping it happening again

Fit an inlet filter. Screws onto the garden hose connection in seconds, catches sediment before it ever reaches the pump or the tip, and rinses out rather than needing replacement. Close to essential on well water or an old outdoor tap.

Never lay a tip on the ground. That is how sand gets into the orifice in the first place. Use a holder, or a pocket.

Flush clear water through at the end of every session, including through the soap setting. Thirty seconds.

Run the first few seconds of garden hose water onto the lawn before connecting, especially on a tap that has sat all winter. The rest of the end-of-season routine is in how to winterize a pressure washer.

What to buy for this

Twinkle Star Nozzle Tips, 5-Pack - Twinkle Star pressure washing gear

Replacing the tips you lost

Twinkle Star Nozzle Tips, 5-Pack

Twinkle Star

Our score

The full color set for the price of a coffee - and the colors are the single most useful thing to understand about a pressure washer.

What it is

  • Five tips: 0, 15, 25, 40 degrees and soap
  • 1/4-inch quick connect
  • Rated 2.5 GPM

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
9.4
Capability
7.6
Build
7.0
Value
9.8

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Covers every job: concrete, siding, cars and soap
  • Universal 1/4-inch quick connect fits almost every machine
  • Cheap enough to keep a spare set in the car

Good to know

These are rated for 2.5 GPM, which matches most homeowner machines.

Tool Daily Nozzle Kit, 4-Pack (1-2 GPM) - Tool Daily pressure washing gear

Low-flow electric machines specifically

Tool Daily Nozzle Kit, 4-Pack (1-2 GPM)

Tool Daily

Our score

A four-tip set rated 1 to 2 GPM, which is the flow range almost every electric pressure washer actually sits in - and almost no generic tip set states.

What it is

  • Four nozzle tips
  • Rated 1-2 GPM
  • Quick connect

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
9.0
Capability
7.6
Build
7.2
Value
9.2

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Correctly sized for 1.2 to 2 GPM electrics, so you keep your pressure
  • States its flow rating, which most budget sets do not
  • Covers the four spray angles that matter

Good to know

The orifices are sized for 1-2 GPM machines, so this is the electric-machine set.

M MINGLE Inlet Water Filter - M MINGLE pressure washing gear

Protecting the pump cheaply

M MINGLE Inlet Water Filter

M MINGLE

Our score

A garden-hose inlet filter that catches the grit which kills pump valves - the cheapest thing on this site and arguably the highest return.

What it is

  • Garden hose inlet filter
  • Fits standard 3/4-inch hose thread

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
9.4
Capability
7.0
Build
7.0
Value
9.6

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Pump failure is the usual death of a pressure washer, and grit is a common cause
  • Screws on in seconds with no tools
  • Rinse and reuse rather than replace

Good to know

Rinse the screen every few uses, or it starts restricting flow.

Common questions

How do I clear a clogged pressure washer nozzle?

Shut the machine off, release the pressure, pull the tip out, and push a cleaning wire or paperclip through the orifice from the spray side toward the inlet side. Then back-flush it with water. Two minutes.

Why did my pressure washer suddenly lose pressure?

A partly blocked nozzle tip is the most common cause by a wide margin. Check and clean the tip before investigating the pump, the unloader or the hose - it costs two minutes and solves it most of the time.

Can I use a drill bit or a nail to clean a nozzle?

No. Anything that can enlarge or score the orifice permanently ruins the spray pattern. Use the supplied cleaning wire, a paperclip or a guitar string - something that fits through without cutting.

How do I know if the nozzle is worn out rather than blocked?

Test on concrete after cleaning. A good tip throws a crisp, even fan with defined edges. If the pattern stays ragged, misted or uneven after cleaning and back-flushing, the orifice is worn and the tip needs replacing.