Skip to content
Pressurewasher & Patio

Pressure washer gun leaking

Where it drips tells you what broke. Four places, four answers.

Pressure washer gun leaking - Tool Daily Pressure Washer Gun
By Mike M.|Last checked: |How we pick

A leak at the tip or the hose connection is almost always a tired O-ring and costs you pennies. A leak from the trigger or the handle body means the internal valve seals have failed, and on a homeowner gun that is a replacement rather than a repair — the parts are not sold separately and a rebuild kit, where one exists, costs more than a new gun. So the first thing to establish is not why it leaks but where.

Find the leak by location

Where the water appearsMost likely causeFix
At the nozzle tip or the collarO-ring on the tip or in the couplerReplace the O-ring
Where the wand meets the gunO-ring, or a cross-threaded fittingO-ring, or the correct adapter
Where the hose meets the gunO-ring, or mixed M22-14 and M22-15 partsO-ring, or match the fitting size
From the trigger or the handle seamInternal valve seals have failedReplace the gun
Only a dribble when the trigger is releasedNormal residual drain, or a weeping valveWatch it; replace if it worsens

Before you touch anything

Turn the machine off, shut the water off, and squeeze the trigger until the flow stops. A high-pressure hose stores energy after shutdown, and a fitting that lets go while you are holding it is a real injury. The general rules are in pressure washer safety for beginners.

Then dry everything with a rag and run the machine again for ten seconds while watching. A wet gun tells you nothing — a dry gun with one wet spot tells you everything.

Leaking at the tip or the collar

The quick-connect coupler has a small O-ring inside it, and the nozzle tip has one on its shank. Either can be pinched on insertion, cracked by age, or simply gone — they drop out unnoticed when you change tips over gravel.

Pull the tip, look at both O-rings against a light background, and replace anything that is flattened, nicked or missing. O-ring assortment packs cost almost nothing and this is the single most common leak on the machine. While you are there, check the tip is not partly blocked, because a blockage raises pressure behind it and makes a marginal seal leak — how to clean a clogged nozzle.

Leaking where the wand screws into the gun

Same O-ring story, plus one more possibility: you may have the wrong fitting. M22 comes in 14mm and 15mm internal sizes which look identical, and a 15 on a 14 will seat but weep forever. If a new O-ring does not fix it, measure the fitting rather than tightening harder — over-tightening a brass fitting deforms the seat and makes the leak permanent. Which adapter matches which mismatch is in the quick connect fittings page.

Leaking where the hose meets the gun

Check in this order. The O-ring, as above. The fitting size, as above. The hose crimp — if water is seeping from the collar where the fitting is swaged onto the hose itself, the hose has failed and no amount of sealing at the gun will help. A hose weeping at the crimp is on its way to bursting; replace it. Hose picks here, and how to choose a hose for sizing.

One thing not to do: wrap the threads in PTFE tape. High-pressure fittings seal on an O-ring or a machined cone face, not on the thread, and tape mostly just hides the problem while making the next disassembly worse.

Leaking from the trigger or the handle

This is the one that means the gun is finished. Inside the handle there is a valve stem with seals that open when you squeeze and close when you release. When those seals wear, water escapes into the handle body and out through the trigger slot or the shell seam.

Homeowner guns are sealed assemblies: the seals are not sold individually, and where a rebuild kit exists it usually costs more than a replacement gun that is better than the original. A good aftermarket gun is rated far above any homeowner machine — 5,000 PSI on a 2,500 PSI unit is correct sizing, not overkill — and usually adds a swivel at the hose end, which makes a long session noticeably less annoying. Options in best pressure washer guns.

If your foam cannon is also tired, replacing the gun and the cannon together as one assembly works out cheaper than buying them separately — which is the case for the combination pick on this page and in best foam cannons.

The leak that is not a fault

A few drops from the tip when you release the trigger is normal: the wand is simply draining. So is a brief dribble when you disconnect a fitting. What is not normal is a steady drip that continues while the machine sits pressurized, or any leak that grows during a session.

Also worth separating from a gun leak: water weeping from the pump head or from under the machine. That is a different problem with different causes, and it belongs in pressure washer will not build pressure and how long do pressure washers last.

Making the next gun last longer

Do not dry-fire it. Running the pump with no water, even briefly, cooks seals in both the pump and the gun.

Engage the trigger lock between passes rather than leaving the gun pressurized and loose on concrete where it can be stepped on.

Keep grit out. An inlet filter protects the gun’s seals as much as the pump’s.

Drain and store it dry over winter. Freezing water in a gun splits the body, and pump saver is a minute of work — winterizing, step by step.

What to buy for this

Tool Daily Pressure Washer Gun - Tool Daily pressure washing gear

Replacing a leaking stock gun

Tool Daily Pressure Washer Gun

Tool Daily

Our score

A 5,000 PSI-rated gun with a 3/8-inch swivel connector, which is the fitting that stops your hose from twisting itself into a knot.

What it is

  • Rated 5,000 PSI
  • 3/8-inch swivel quick connector
  • Quick-connect wand fitting

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
8.0
Capability
8.6
Build
8.4
Value
8.4

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • The swivel alone makes a long session less annoying
  • Rated well above any homeowner machine, so it is not the weak link
  • Fits the common quick-connect standards

Good to know

An M22 machine outlet may need the matching adapter.

3/8in to 1/4in Quick-Connect Adapters, 2-Pack - Generic pressure washing gear

The part that makes mismatched fittings work

3/8in to 1/4in Quick-Connect Adapters, 2-Pack

Generic

Our score

Two 3/8-inch male to 1/4-inch female adapters, which is the exact piece missing when a new accessory will not screw onto your gun.

What it is

  • 3/8-inch male to 1/4-inch female
  • Two-pack
  • Quick connect

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
8.6
Capability
7.4
Build
8.0
Value
8.6

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Fixes the most common fitting mismatch on the first try
  • Two in the pack, so one lives with the gun and one with the surface cleaner
  • Cheap insurance against a wasted Saturday

Good to know

It solves one direction of mismatch, so check which end you need.

See today's price on the 3/8in to 1/4in - $27.99

$32.99 15% off

#ad Price as of November 18, 2026. How this is funded

M MINGLE Gun with Foam Cannon - M MINGLE pressure washing gear

Gun and foam cannon in one buy

M MINGLE Gun with Foam Cannon

M MINGLE

Our score

A replacement gun bundled with a foam cannon and both common connectors - the single cheapest route from bare machine to washing a car properly.

What it is

  • Gun with foam cannon
  • Dual connector set included
  • Accessory kit

Specs from the Amazon catalog listing.

Rubric marks

Ease of use
8.6
Capability
8.0
Build
7.4
Value
9.0

Raw rubric marks out of 10. The score above places them on our published 8.4-9.8 recommendation scale.

Good

  • Solves the gun problem and the foam problem at once
  • Ships with both M22 and quick-connect fittings, which removes the usual guesswork
  • Good value against buying the two separately

Good to know

Foam thickness depends on your machine's GPM more than on the cannon.

Common questions

Why is my pressure washer gun leaking at the tip?

Almost always a worn, pinched or missing O-ring - either on the nozzle tip's shank or inside the quick-connect coupler. Pull the tip, inspect both, and replace anything flattened or nicked. It is a pennies-level fix.

My gun leaks from the trigger. Can I repair it?

Practically, no. A leak from the trigger or the handle seam means the internal valve seals have failed, and on homeowner guns those are not sold separately. Replace the gun with one rated above your machine's working pressure.

Should I use plumber's tape on pressure washer fittings?

No. High-pressure fittings seal on an O-ring or a machined cone face, not on the thread. Tape masks the real problem and makes the next disassembly harder.

Is a small drip from the nozzle normal?

A few drops after releasing the trigger is just the wand draining. A steady drip while the machine sits pressurized, or a leak that worsens during a session, is a failing seal.